How to Recover Data from Failed Solid State Drive?

Rate this post

Unlike normal SD cards or hard disks, Solid State Drive (SSD) is a little different. It is sensitive to automated damage or failure because of sudden drop or shock. But SSDs can fail because of electronic reasons or physical damage.

We know that data loss is a bleak situation. But you can prevent your SSD from this situation. Well, no doubt whenever users lose their data, they seek data recovery software for the first time. On the other hand, whenever you face such issues, first relax your mind and then decide on the next steps to save data from your SSDs.

So, to suggest the best tips, we have created a guide regarding lost data recovery from solid state drives. Furthermore, we have mentioned some common causes of failure and steps to prevent your SSDs.

Checkout Pre Symptoms Of SSD Failing

Commonly, detecting SSDs failure is not an easy task for a layman. Even the SSDs don’t emit noise or signals such as clicking, humming, or whirring while shutting down completely. Mostly SSDs work in silence till they stop working.

However, your SSDs show a warning signal. It is enough to inform users about the impending danger. If you have good knowledge of a Solid state drive, you can detect the signal of SSD failure. Once you get a warning, you can take relevant steps to save it from failure.

Tips For Fixing Your Failed SSD

If there are any physical issues such as degraded flash cells or hardware damage, you need to replace your SSDs. So, an expert with some knowledge of SD card data recovery may help you. There could be a few dysfunctions in SSDs like; Bad blocks, Software malfunctions, Malware, Outdated firmware, etc.

Now check out the most common ways for recovering data from a failed SSD.

1. Power cycling the Solid State Drive.

Power cycling is the best-suited solution if your SSD drive gets corrupted because of power failure. Initially, do unplug the SATA data cable. However, let the power cable in. 

  • Now, on the power for approx 30 to 40 minutes, later turn off for about 30 seconds. 
  • Power on again for approx 30 minutes. 
  • At last, turn the power off for the next 30 seconds. 
  • Turn on the power back, then reconnect the cable. 

Following this process will be effective, your SSDs will start back up. 

2. Idling in the boot menu

The idling boot menu is the same process as the power cycling method. Turn the power on every 30 minutes, leave your device idle in the boot menu. 

For Mac users: Go to the boot menu turn on your iMac while holding the ALT key.

For Windows: On your PC, boot into BIOS, then sit at the BIOS screen. 

3. Update driver

If you are a Windows user, check the Device Manager, click the disk drives, and update the driver by right-clicking on the SSD. Once you reboot, you can observe the revived SSD.

4. Update SSD firmware

The storage drive’s firmware might have been corrupt. If the firmware is not good, this may impact the ability of the drive to write, read, or access data. If you run a firmware update tool, you can check the version of the SSD. If your drive doesn’t have the latest version, then install it. Later you will see the functionality is restored.

The experts would not reverse the impact when the firmware is damaged, losing confidential data.

Common Warnings Displays Before SSD Fails 

Below we have listed some of the very common and basic warnings that your SSDs may show. Moreover, we have compiled a list of indicators that pop up before experiencing physical damage or its read/write cycle limit. Please have a look over them!

1. SSDs crash

When your system crashes while booting up but still works after you boot up 3 or 4 times, then, unfortunately, your SSD has failed. If this is the situation, you can try several techniques:

  • Assess health and the performance of SSDs by software.
  • Install your operating software again.
  • Clear all data saved on the partition set.

These tips will solve the problem on a temporary basis, and you have to buy a new SSD because it can stop working anytime.

2. File system repair

When your device (computer or laptop) demands repair, however, physical defect software doesn’t show any damages, it means there is a problem with the connector port. If this is the condition, first back up all your data or important files before any other step. Later you can opt for hard disk data recovery of your Mac or Windows OS.

  • A Linux user, runs the fsck utility.
  • If you use iOs, utilize Disk Utility.
  • If you use a different OS, check for other premium software or free software options.

3. Read-only issue

Well, the read-only mode is one of the most uncommon problems. It is possible when SSDs stop functioning and go read-only. In this case, your Solid State Drive will not follow any command. It simply means the drive is probably corrupted. Here you have to secure data by a backup.

4. Bad blocks

Bad blocks are one of the major issues in the SSDs. If your SSD has bad blocks issues, then it exhibits some issues like:

  • Saving files failure
  • Reading files failure
  • Moving documents failure

Also, active apps will crash frequently or run slowly. The users might face problems in repairing the file system. The performance of the device will decrease, particularly when managing large files.

Once you find the above issues in your SSDs and observe bad blocks, choose data recovery software to save your disk or drive. The software will find physical defects, if any. Once you find physical damage, backup all the essential documents and note that it’s time to replace your SSD.

Final Words 

So are you ready to recover data from your failed SSD? Well, this article might give you a clear vision of fixing a failed SSD as well as some visual signs to prevent damage. If you can’t do it by yourself, then hard disk data recovery in Singapore could be the right choice. Furthermore, the recovery center has experts to solve the issues regarding SD cards, hard disks, or SSDs. 

Leave a Reply

Your email address will not be published. Required fields are marked *